5 Phase Dual Axial Flux Generator Calculator
Estimate open-circuit voltage, frequency, and 5-phase geometry attributes for dual rotor AFPM generators.
Key Design Insights for 5-Phase Dual Rotor Topologies
Fault tolerance depends on the drive design
A five-phase winding can support controlled operation after some open-circuit faults, but only with suitable current regulation and inverter topology. This calculator does not assess faulted operation or torque ripple.
Two distinct line voltages exist
For a balanced sinusoidal five-phase star connection, adjacent phases are 72° apart and non-adjacent phases are 144° apart, so their line-to-line RMS voltages differ.
Source: Derived from the balanced five-phase voltage phasors.
Dual-rotor geometry is not solved by this screen
The estimate uses the entered peak fundamental air-gap flux density over one active annulus. It does not model the two air gaps, leakage, magnet shape, or stator construction, and does not double area or voltage for two rotors.
Source: Model scope: this tool does not solve dual-gap field geometry.
Need a detailed winding-aware review of a 5-phase estimate? Share your coil layout, fault tolerance goals, and operating limits with the engineering team.
Request engineering reviewMethodology & Sources
| Source | Usage | Limitation |
|---|---|---|
| Asko Parviainen, Design of Axial-Flux Permanent-Magnet Low-Speed Machines and Performance Comparison between Radial-Flux and Axial-Flux Machines, §2.2.4 (2005)Reviewed: | Reference for fundamental no-load phase-voltage estimation from air-gap flux, series turns, frequency, and winding factor. This page uses the sinusoidal 4.44 f N Φ form. | This thesis models a different axial-flux topology. It supports the voltage equation only; this calculator simplifies the field to a uniform annulus and does not model leakage, loaded voltage drop, saturation, or harmonics. |
| Fault-tolerant operation for five-phase permanent-magnet synchronous machine drives with five-phase six-leg inverter (Wu et al., IET, 2024)Reviewed: | Evidence that degraded operation after open-circuit faults depends on current regulation and inverter topology. | This is a drive-system study, not a validation of this generator calculator or of any specific machine design. |
| Five-Phase Line Commutated Rectifiers, §2 (IntechOpen)Reviewed: | Reference for balanced five-phase phasors and the distinct adjacent and non-adjacent line-voltage ratios. | The chapter explains an ideal five-phase source and rectifier; it does not validate a generator winding or loaded operating point. |
Calculation basis
- Electrical frequency:
f = poles × RPM / 120. - Flux per pole:
Φ ≈ (2/π) × Bpeak × annulus area / poles, assuming a sinusoidal field over a uniform annulus. - Open-circuit phase voltage:
Ephase ≈ 4.44 × f × turns per phase × kw × Φ. The model assumes all entered coils are series-connected as equal groups across five phases. - Star-connected line voltage:
Vline = 2 × Vphase × sin(phase separation / 2). This gives 72° for adjacent phases and 144° for non-adjacent phases.
These are screening equations. Confirm the actual winding diagram, flux waveform, connection, insulation, current, thermal limits, and loaded voltage before selecting hardware. Default values are illustrative inputs, not measured test results or a generator rating.
The 400 Hz frequency and 1,000 V line-voltage alerts are this tool's screening triggers, not validated performance limits or compliance thresholds.
5-Phase Dual Axial Flux Generator FAQ
What does this 5-phase generator calculator estimate?
It estimates electrical frequency, open-circuit RMS phase voltage, and star-connected line voltages (adjacent and non-adjacent) from speed, active annulus dimensions, pole/coil counts, peak fundamental air-gap flux density, winding factor, and turns per coil. It does not predict loaded voltage or rated power.
Why does a 5-phase generator have two line voltages?
A 5-phase system has phases separated by 72 electrical degrees. Measuring voltage between adjacent phases (e.g., A and B) gives a different result than measuring between non-adjacent phases (e.g., A and C, separated by 144 degrees).
Is this calculator for coreless or iron-core stators?
It is a first-pass voltage screen for either construction if you supply a suitable peak fundamental air-gap flux density and winding factor. It does not model cogging torque, stator-core loss, magnet eddy-current loss, or winding temperature.
What does the pole-count and coil-count warning mean?
Equal pole and coil counts are not automatically invalid. The warning means this screening model cannot verify the actual coil layout, winding factor, back-EMF harmonics, or cogging torque; check the winding diagram before choosing a design.
Request OEM Generator Support
Need to prototype or manufacture a custom 5-phase axial flux generator? Send us your requirements (RPM, voltage target, torque limit, packaging constraints) and our engineers will assist with feasibility and pricing.
Inquiry Email
Please include application, peak/continuous torque, speed range, voltage/current limit, outer diameter, axial length, cooling method, quantity, and drawings or reference samples.
Instant Chat
+86 188 5797 1991
Share torque-speed, package, cooling, and sample quantity in the first message.